When you change your own oil, you know that you are putting quality oil in your Camry and that the filter is being changed too. . Any other engine has the filter underneath the car. If you can't do this, see our page to find a Toyota Camry oil filter wrench. This video shows you how to change the oil and oil filter in your 2003 Toyota Camry.
Permit your engine to operate at the most efficiency and travel with assurance. Most importantly, you get a chance to look around under your Camry for potential trouble spots. All Toyota Camry models use the same process when changing the oil. It is crucial to change outdated and worn-out parts mainly because they operate improperly. Started in 1999, aFe Power is known for its innovative design and manufacturing standards with regard to filters and cold air intakes for most road-going vehicles.
If it's not at full, turn off the engine and add more oil. Slide under the car and locate the drain plug and filter, if necessary. Camry's dated 1983-1988 use 15W-40, 20W-40, 20W-50, 10W-30, 10W-40, 10W-50 or 5W-30 oil. Change the Oil Take the closed end wrench or metric socket and remove the drain plug. A newer Camry, specifically models made from 1997 to 2000, have the oil filler cap on the valve cover. Camry's dated 1992 and on use 10W-30 or 5W-30 oil.
If your filter is located under the front exhaust manifold, slide out and look under your hood for the filter. Check the oil level on the dipstick. We recommend wearing safety glasses whenever you are working under your Camry. Repairing or modifying your motor vehicle generally involves replacing auto parts. If it isn't printed on the oil cap, check your owners manual for the exact type before adding new oil. Lower your car and shut the hood.
For a Camry dated 1989-1991, use 10W-40, 10W-30 or 5W-30 oil. You never know what could be dripping down from the engine, battery acid, engine coolant, brake fluid, etc. If your Camry is too low to the ground to access your drain plug and oil filter, be sure to use jack stands and safe jacking procedures before getting under your Camry. Make sure you brace the backs of the front tires, so the car doesn't roll. Start your car for about a minute and let the oil pressure build. The drain plug is usually on the bottom rear of the oil pan, with the filter near the front.
Most Toyotas have the oil type printed on the oil cap - it will likely be 5W-20, 5W-30, 5W-40, 10W-30 or 10W-40. This video shows you the location of your oil drain plug, oil filter, oil fill cap and dipstick in addition to the steps needed to change the oil and filter in your Camry. So browse around our great selection of car parts and let's help with that auto repair or car upgrade! Coat the rubber gasket of the new filter with oil and replace the oil filter. Check the threads of the plug for damage and clean off excess oil. Slide out from under your car and fill your car with oil.
The 5W oil is for colder temperatures and is the preferred oil for most vehicles. For most Toyotas, you can wrap an old belt around the oil filter and unscrew it by hand. All of these fluids are extremely harmful to your eyes and skin so it is important to protect yourself. Replace the drain plug and move over to the filter. If you don't have jack stands, you can drive your car up onto a set of wheel ramps. Gather an oil drip pan, new filter, closed end wrench or metric socket and cleaning cloths.
However, depending on the age of your Camry, your car might take a different oil than a newer Camry. Pop the hood and locate the oil filler cap and dipstick. The filter locations change too, depending on the type of engine in your Camry. Using a filter wrench, remove the filter and dump the oil into your oil drip pan. Pull the plug quickly, and let the oil drain into the pan for approximately 10 to 15 minutes.
Check what type of engine is in your Toyota Camry. Remove the cap and dipstick. Prepare Your Camry for an Oil Change Lift your Camry up using a car jack and then set jack stands underneath it. . . .