Posted on Nov 23, 2014 Battery-Goes- Dead-after-A-F. Helicoil® is a registered trademark of Emhart Industries Inc. Perform the fuel pressure test as per the instructions in the manual to ensure the most accurate test results. Then give the battery a good charge if possible and try again. Therefore, diagnosing and repairing code P062F requires professional grade diagnostic equipment, above average diagnostic skills in general, and expert-level knowledge of the application being worked on in particular.
I went to turn it on today but the starter just turns over and doesn't sound like it's firing at all. To prevent the possibility of an engine fire, only start the engine once it is certain sure that the gauge is attached securely. Oil doesn't move well inside the engine at that temperature. The image below shows a Fuel Control Module that had failed because of corrosion of the metal casing. I cranked the engine and sprayed some gas into the intake and it runs. These terms are used for identification purposes only. Step 3 When all wiring is checked and reconnected, clear the code, and re-test the system to see if the code returns.
Optikleen® is a registered trademark of General Motors Corporation. On some applications this can be done without a scanner, but whatever the method applicable to the application, clear the code and operate the vehicle for at least two complete drive cycles to see if it returns. Torx® is a registered trademark of Camcar Div. Performance chips and products are not created equal, meaning that some after market performance chips and programs can and do fail unexpectedly. This option should be considered as a first step in the diagnostic and repair procedure, since the process of reprogramming is relatively inexpensive, as opposed to the potentially huge repair bill that comes with attempting to diagnose and repair say, bad connections or abnormal resistances that may, or may not, be present in any one or more of hundreds of circuits. Apr 02, 2011 Battery can be so dead that it won't take a jump. A block heater and a battery heater , if you don't already have them , should be used.
We scanned the vehicle and it came up with code P069E. Note however that since returnless fuel systems do not have the ability to bleed off excess pressure, the system relies on very accurate data from the fuel pressure sensor in order to avoid both over-, and under fuelling conditions. Instead, consult the manual on the location of all ground connection points on the vehicle, and perform a thorough visual inspection of all connections, but be aware that it may be necessary to remove seats, carpets, trim panels, and parts of the dashboard to gain access to all ground connections. I have left my car unused for a few days and the battery still started the car. If you have any doubt as to repairs on your vehicle, please contact your technician. If it is newer than 5 years old, charge battery on a battery charger for enough time to properly charge it.
I notice the engine light so I grabbed my code reader and pulled the code. Also determine the routing, function, and color-coding of all associated wiring, and especially the wiring that is associated with the fuel pressure sensor. Look for damaged, burnt, shorted, disconnected, or corroded wiring and connectors, and make repairs or replace wiring as required. © 2018 Madison Ross Media Group. All information on this site is the opinion of its members and not the opinion of the site itself. Teflon® is a registered trademark of E. Always consult the manual for the application being worked on for detailed information of possible symptoms of code P062F as it pertains to that application.
If no visible damage to wiring is found, perform resistance, reference voltage, ground, and continuity checks on all its associated wiring. In many cases, the code may be an artefact of a low system voltage or similar transient issue, and clearing P062F is often sufficient to resolve the problem. . The information contained on this site is presented for informational purposes only. Compare all obtained readings with the values stated in the manual, and repair or replace wiring as required to ensure that all electrical values fall within the ranges specified by the manufacturer.
This information can be of use should an intermittent fault be diagnosed later on. For instance, on many Toyota products, this code refers to the programming of the fuel injectors, while on some Nissan and Chevrolet products the code refers to issues with the transmission and throttle control programming respectively. Goodwrench® is a registered trademark of General Motors Corporation. From a safety perspective, it is highly recommended that in cases where an intermittent fault is suspected, the vehicle be referred to the dealer or other competent repair facility for professional diagnosis and repair. If there is, then a complete fuel system flush is in order and replace the fuel filter. Hi brentil, I am sorry that your wife is in the hospital; I wish her a speedy recovery.
Step 1 Record all codes present, as well as all available freeze frame data. How do you troubleshoot code P062F? If no visible damage to wiring is found, perform resistance, reference voltage, ground, and continuity checks on all its associated wiring. Be aware though that removing a fuel pump on some applications may require removal of the fuel tank, so consult the manual on the correct procedure to gain access to the fuel pump. Look for damaged, burnt, shorted, disconnected, or corroded wiring and connectors, and make repairs or replace wiring as required. Thus, if the fault does not return after having completed the required number of drive cycles, the repair can be considered as successful. In extreme cases, it may be necessary to allow the fault to worsen considerably before an accurate diagnosis and definitive repair can be made. Step 4 Locate the fuel pressure sensor, and perform a thorough visual inspection of all associated wiring.
That's all I can offer you as you don't say why you think you have a dead battery. If all electrical values check out, replace the Fuel Pump Control Module, especially if there are any signs of corrosion on the casing if the module is made of metal. Nov 08, 2015 that is because it is dead? Other symptoms of this code are mostly make and model specific, and depending on the application, could include non-starting conditions and serious driveability problems. The list of automotive Makes at the right edge of the screen. Make repairs or replace wiring as required to ensure that all electrical values fall within the ranges specified by the manufacturer. P062B Buick Internal Control Module Fuel Injector Control Performance Anyone have any suggestions or idea exactly what this means? Enter the 5 character trouble codes in the search box and submit the search. Is there room under the hood to run a dual-battery set-up? Step 7 Note that on some applications, completing multiple drive cycles may be required before this code can be cleared.
If your are for a different car, select that vehicle series before searching for the diagnostic codes because not all used by one manufacture are used by the other makes. Mar 03, 2015 place the positive lead from the jump battery to the positive terminal of the dead battery. Will see if the check engine light returns in the next 48 hours. However, a major complication with this code is the fact that the memory, or programming that has suffered damage, or is lost , varies between applications. Make sure the engine is warmed up some before you try to start it. Motorcraft® is a registered trademark of Ford Motor Company.